18 Zone Conventional Fire Alarm Control Panel Fire Alarm System for Factory

• Customization: Available
• Type: Fire Alarm Host
• Function: Networked
• Model NO.: CP1018
• Usage: Fire, Smoke
• Certification: CE
• Alarm Volume (within 1m): ≥100dB
• Networking Mode: Alarm
• Receive Frequency: 485/232
• Wiring Mode: Sub-Line System
• Weight: 5kg
• Color: Gray
• Number of Zones: 18
• Primary AC: 90-270VDC
• Standby Battery: 2*12V
• Transport Package: Carton
• Specification: 325x265x100mm
• Trademark: panel
• Origin: China
• HS Code: 8531100000
• Production Capacity: 500000/Month

Product Description

CONTROL PANEL
The fire panel must be sited internally, in an area
where it is readily accessible by staff on duty and the
fire brigade. The area should be clean and dry and
you should take into account any likelihood of
tampering or vandalism. The ambient light and
sound levels should allow the status of the indicators
to be clearly seen and the internal sounder to be
heard. Full details can be found in BS 5839: Pt1: 1988:
Section 15.3 "Fire Detection and Alarm Systems for
Buildings".

External (key-switch operated):

• Reset/resound/test zone lamps evacuate
• Silence alarm sounders
• Silence fault sounders

Internal:

• One man detector test
• Zone isolate
• Revert to short-circuit: fire (no resistors in call points)

External indicators:

• Sounder fault
• Battery/power supply fault
• Mains on
• Zone fire
• Zone fault

Internal indicators:

• Open circuit zone fault
• Short circuit zone fault
• Zone isolated
• Engineer test selected

Outputs:

• Two sounder circuits (alarm relay contacts can be obtained by connecting a relay to a sounder circuit)

Ancillary connections for expansion modules will allow the following:

• Repeater panels
• Multiple sounder outputs
• Connection to landlord panel

 

 Specifications 

	2 (0.8A supply)	4 / 6 (1.5A supply)	8/10/12/14/16/18 (4.0A supply)
Power specifications
Mains supply voltage	230±10%V AC, 50/60Hz	230±10%V AC, 50/60Hz	230±10%V AC 50/60Hz
Internal power supply	27V DC	27V DC	27V DC
Total output current limited to	800mA at 240V AC	1500mA at 240V AC	4000mA at 240V AC
Auxiliary power output	27V DC	27V DC	27V DC
Mains supply monitored for failure	Yes	Yes	Yes
Battery charger monitored for failure	Yes	Yes	Yes
Batteries monitored for disconnection and failure	Yes	Yes	Yes
Detector circuit specification
Number of circuits	2	4 or 6	8, 10, 12, 14,16,or 18
Line fault monitored for open circuit	Yes	Yes	Yes
Line fault monitored for short circuit	Yes (can be disabled)	Yes (can be disabled)	Yes (can be disabled)
Line fault monitored for detector removal	Yes, if end of line monitor unit fitted in place of end of line resistor
End of line resistor (supplied) value	6.8K Ohm, 5% tolerance, 0.25W	6.8K Ohm, 5% tolerance, 0.25W	6.8K Ohm, 5% tolerance, 0.25W
Detector continuity diodes	Silicone 1N4001 or Schottky type (required if end of line monitor unit fitted to give detector removal fault)
Call point resistor value (not supplied)	470 to 680 Ohm, 0.5W	470 to 680 Ohm, 0.5W	470 to 680 Ohm, 0.5W
Maximum number of smoke detectors per zone	20 (maximum detector current = 2mA)	20 (maximum detector current = 2mA)	20 (maximum detector current = 2mA)
Maximum number of manual  call points per zone	No limit	No limit	No limit
Sounder circuit specifications:
Number of circuits	2	2	2
End of line resistor value	6.8K Ohm, 5% tolerance, 0.25W	6.8K Ohm, 5% tolerance, 0.25W	6.8K Ohm, 5% tolerance, 0.25W
Line fault monitored  for open circuit	Yes	Yes	Yes
Line fault monitored for short circuit	Yes	Yes	Yes
Outputs fused at	1A	1A	1.6A
Maximum total output current all outputs	800mA	1500mA	4000mA
Maximum no of bells at 25mA each bell	32	56	120
Maximum no of electronic sounders at 20mA	40	70	150
Auxiliary relay contacts  (do not connect mains voltages)	1A 30V DC max   voltage free	1A 31V DC max   voltage free	1A 32V DC max   voltage free
Fuses-all fuses compliant to ice (EN60127 PT2)
Mains terminal block	200mA/T 20mm	400mA/T 20mm	630mA/T 20mm
Sounder outputs	1A/F 20mm	1A/F 20mm	1.6A/F 20mm
Auxiliary output	1A/F 20mm	1A/F 20mm	1A/F 20mm
Battery fuse	1.6A/F 20mm	1.6A/F 20mm	3A/F 20mm
Door retaining magnets	do not use panel power supply as you will drastically reduce battery standby time
Connection block
Largest acceptable	2.5mm^2	2.5mm^2	2.5mm^2
Smallest acceptable conductor size	0.75mm^2	0.75mm^2	0.75mm^2
Dimensions
Enclosure (width x height x depth)	415 x 265 x 100mm	415 x 265 x 100mm	415 x 265 x 100mm
Weight (without batteries)	5100g	5200g	5500